1. Home
  2. College physics for ap® courses
  3. Magnetism
  4. Magnetic force between two

22.10 Magnetic force between two parallel conductors  (Page 2/2)

<< Chapter < Page
  College physics for ap® courses     Page 2 / 2
Chapter >> Page >

This force is responsible for the pinch effect in electric arcs and plasmas. The force exists whether the currents are in wires or not. In an electric arc, where currents are moving parallel to one another, there is an attraction that squeezes currents into a smaller tube. In large circuit breakers, like those used in neighborhood power distribution systems, the pinch effect can concentrate an arc between plates of a switch trying to break a large current, burn holes, and even ignite the equipment. Another example of the pinch effect is found in the solar plasma, where jets of ionized material, such as solar flares, are shaped by magnetic forces.

The operational definition of the ampere is based on the force between current-carrying wires. Note that for parallel wires separated by 1 meter with each carrying 1 ampere, the force per meter is

F l = 4π × 10 − 7 T ⋅ m/A 1 A 2 2 π 1 m = 2 × 10 − 7 N/m. size 12{ { {F} over {l} } = { { left (4π times "10" rSup { size 8{ - 7} } `T cdot "m/A" right ) left (1`A right ) rSup { size 8{2} } } over { left (2π right ) left (1" m" right )} } =2 times "10" rSup { size 8{ - 7} } " N/m" "." } {}

Since μ 0 size 12{μ rSub { size 8{0} } } {} is exactly 4π × 10 − 7 T ⋅ m/A by definition, and because 1 T = 1 N/ A ⋅ m size 12{1" T"=" 1N/" left (A cdot m right )} {} , the force per meter is exactly 2 × 10 − 7 N/m size 12{2 times "10" rSup { size 8{ - 7} } `"N/m"} {} . This is the basis of the operational definition of the ampere.

The ampere

The official definition of the ampere is:

One ampere of current through each of two parallel conductors of infinite length, separated by one meter in empty space free of other magnetic fields, causes a force of exactly 2 × 10 − 7 N/m size 12{2 times "10" rSup { size 8{ - 7} } " N/m"} {} on each conductor.

Infinite-length straight wires are impractical and so, in practice, a current balance is constructed with coils of wire separated by a few centimeters. Force is measured to determine current. This also provides us with a method for measuring the coulomb. We measure the charge that flows for a current of one ampere in one second. That is, 1 C = 1 A ⋅ s size 12{1`C=1`A cdot s} {} . For both the ampere and the coulomb, the method of measuring force between conductors is the most accurate in practice.

Test prep for ap courses

Two parallel wires carry equal currents in the same direction and are separated by a small distance. What is the direction of the magnetic force exerted by the two wires on each other?

  1. No force since the wires are parallel.
  2. No force since the currents are in the same direction.
  3. The force is attractive.
  4. The force is repulsive.

(c)

Got questions? Get instant answers now!

A wire along the y -axis carries current in the + y -direction. An experimenter would like to arrange a second wire parallel to the first wire and crossing the x -axis at the coordinate x   =   2.0  m so that the total magnetic field at the coordinate x   =   1.0  m is zero. In what direction must the current flow in the second wire, assuming it is equal in magnitude to the current in the first wire? Explain.

Got questions? Get instant answers now!

Section summary

  • The force between two parallel currents I 1 size 12{I rSub { size 8{1} } } {} and I 2 size 12{I rSub { size 8{2} } } {} , separated by a distance r size 12{r} {} , has a magnitude per unit length given by
    F l = μ 0 I 1 I 2 2 πr . size 12{ { {F} over {l} } = { {μ rSub { size 8{0} } I rSub { size 8{1} } I rSub { size 8{2} } } over {2πr} } } {}
  • The force is attractive if the currents are in the same direction, repulsive if they are in opposite directions.

Conceptual questions

Is the force attractive or repulsive between the hot and neutral lines hung from power poles? Why?

Got questions? Get instant answers now!

If you have three parallel wires in the same plane, as in [link] , with currents in the outer two running in opposite directions, is it possible for the middle wire to be repelled by both? Attracted by both? Explain.

Diagram showing three wires parallel to each other and in the same plane. The currents in wire 1 on the left side of the diagram and wire 3 on the right side of the diagram run opposite each other: I 1 runs form the top right to the lower left; I 3 runs from the lower left to the top right. Wire 2 is between the two, slightly closer to wire 3 than to wire 1.
Three parallel coplanar wires with currents in the outer two in opposite directions.
Got questions? Get instant answers now!

Suppose two long straight wires run perpendicular to one another without touching. Does one exert a net force on the other? If so, what is its direction? Does one exert a net torque on the other? If so, what is its direction? Justify your responses by using the right hand rules.

Got questions? Get instant answers now!

Use the right hand rules to show that the force between the two loops in [link] is attractive if the currents are in the same direction and repulsive if they are in opposite directions. Is this consistent with like poles of the loops repelling and unlike poles of the loops attracting? Draw sketches to justify your answers.

Diagram showing two current-carrying loops. The planes of the loops are parallel and horizontal, one above the other. In both loops, the current runs counterclockwise.
Two loops of wire carrying currents can exert forces and torques on one another.
Got questions? Get instant answers now!

If one of the loops in [link] is tilted slightly relative to the other and their currents are in the same direction, what are the directions of the torques they exert on each other? Does this imply that the poles of the bar magnet-like fields they create will line up with each other if the loops are allowed to rotate?

Got questions? Get instant answers now!

Electric field lines can be shielded by the Faraday cage effect. Can we have magnetic shielding? Can we have gravitational shielding?

Got questions? Get instant answers now!

Problems&Exercises

(a) The hot and neutral wires supplying DC power to a light-rail commuter train carry 800 A and are separated by 75.0 cm. What is the magnitude and direction of the force between 50.0 m of these wires? (b) Discuss the practical consequences of this force, if any.

(a) 8.53 N, repulsive

(b) This forceis repulsiveand thereforethere isnever arisk thatthe twowires willtouch andshort circuit.

Got questions? Get instant answers now!

The force per meter between the two wires of a jumper cable being used to start a stalled car is 0.225 N/m. (a) What is the current in the wires, given they are separated by 2.00 cm? (b) Is the force attractive or repulsive?

Got questions? Get instant answers now!

A 2.50-m segment of wire supplying current to the motor of a submerged submarine carries 1000 A and feels a 4.00-N repulsive force from a parallel wire 5.00 cm away. What is the direction and magnitude of the current in the other wire?

400 A in the opposite direction

Got questions? Get instant answers now!

The wire carrying 400 A to the motor of a commuter train feels an attractive force of 4 . 00 × 10 − 3 N/m size 12{4 "." "00" times "10" rSup { size 8{ - 3} } `"N/m"} {} due to a parallel wire carrying 5.00 A to a headlight. (a) How far apart are the wires? (b) Are the currents in the same direction?

Got questions? Get instant answers now!

An AC appliance cord has its hot and neutral wires separated by 3.00 mm and carries a 5.00-A current. (a) What is the average force per meter between the wires in the cord? (b) What is the maximum force per meter between the wires? (c) Are the forces attractive or repulsive? (d) Do appliance cords need any special design features to compensate for these forces?

(a) 1 . 67 × 10 − 3 N/m size 12{1 "." "67" times "10" rSup { size 8{ - 3} } `"N/m"} {}

(b) 3 . 33 × 10 − 3 N/m size 12{3 "." "33" times "10" rSup { size 8{ - 3} } " N/m"} {}

(c) Repulsive

(d) No, these are very small forces

Got questions? Get instant answers now!

[link] shows a long straight wire near a rectangular current loop. What is the direction and magnitude of the total force on the loop?

Diagram showing two current-carrying wires. Wire 1 is at the top and runs left to right with the current I 1 of fifteen amps also running left to right. Wire 2 makes a square circuit ten point zero centimeters in the vertical dimension and thirty point zero centimeters in the horizontal dimension. The top side of Wire 2 is seven point five zero centimeters below wire 1. The current in wire 2 is thirty point zero amps and runs counterclockwise: left to right along the bottom, up the right side, right to left along the top, and down the left side.
Got questions? Get instant answers now!

Find the direction and magnitude of the force that each wire experiences in [link] (a) by, using vector addition.

Figure a shows the cross sections of three wires that are parallel to each other and arranged in an equilateral triangle. The bottom left wire has current of ten point zero amps into the page. The bottom right wire has a current of twenty point zero amps also into the page. The wire at the top of the triangle has current five point zero amps out of the page. The triangle that the wires make with each other is ten point zero centimeters on each side. Figure b shows four parallel wires arranged in a square that is twenty point zero centimeters on a side. The top two wires have current of ten point zero amps out of the page. The bottom two wires have current of five point zero amps into the page.

(a) Top wire: 2 . 65 × 10 − 4 N/m s, 10 . 9º size 12{"10" "." 9°} {} to left of up

(b) Lower left wire: 3 . 61 × 10 − 4 N/m size 12{3 "." "61" times "10" rSup { size 8{ - 4} } `"N/m"} {} , 13 . 9º size 12{"13" "." 9°} {} down from right

(c) Lower right wire: 3 . 46 × 10 − 4 N/m size 12{3 "." "46" times "10" rSup { size 8{ - 4} } `"N/m"} {} , 30 . 0º size 12{"30" "." 0°} {} down from left

Got questions? Get instant answers now!

Find the direction and magnitude of the force that each wire experiences in [link] (b), using vector addition.

Got questions? Get instant answers now!

Questions & Answers

A golfer on a fairway is 70 m away from the green, which sits below the level of the fairway by 20 m. If the golfer hits the ball at an angle of 40° with an initial speed of 20 m/s, how close to the green does she come?
Aislinn Reply
cm
tijani
what is titration
John Reply
what is physics
Siyaka Reply
A mouse of mass 200 g falls 100 m down a vertical mine shaft and lands at the bottom with a speed of 8.0 m/s. During its fall, how much work is done on the mouse by air resistance
Jude Reply
Can you compute that for me. Ty
Jude
what is the dimension formula of energy?
David Reply
what is viscosity?
David
what is inorganic
emma Reply
what is chemistry
Youesf Reply
what is inorganic
emma
Chemistry is a branch of science that deals with the study of matter,it composition,it structure and the changes it undergoes
Adjei
please, I'm a physics student and I need help in physics
Adjanou
chemistry could also be understood like the sexual attraction/repulsion of the male and female elements. the reaction varies depending on the energy differences of each given gender. + masculine -female.
Pedro
A ball is thrown straight up.it passes a 2.0m high window 7.50 m off the ground on it path up and takes 1.30 s to go past the window.what was the ball initial velocity
Krampah Reply
2. A sled plus passenger with total mass 50 kg is pulled 20 m across the snow (0.20) at constant velocity by a force directed 25° above the horizontal. Calculate (a) the work of the applied force, (b) the work of friction, and (c) the total work.
Sahid Reply
you have been hired as an espert witness in a court case involving an automobile accident. the accident involved car A of mass 1500kg which crashed into stationary car B of mass 1100kg. the driver of car A applied his brakes 15 m before he skidded and crashed into car B. after the collision, car A s
Samuel Reply
can someone explain to me, an ignorant high school student, why the trend of the graph doesn't follow the fact that the higher frequency a sound wave is, the more power it is, hence, making me think the phons output would follow this general trend?
Joseph Reply
Nevermind i just realied that the graph is the phons output for a person with normal hearing and not just the phons output of the sound waves power, I should read the entire thing next time
Joseph
Follow up question, does anyone know where I can find a graph that accuretly depicts the actual relative "power" output of sound over its frequency instead of just humans hearing
Joseph
"Generation of electrical energy from sound energy | IEEE Conference Publication | IEEE Xplore" ***ieeexplore.ieee.org/document/7150687?reload=true
Ryan
what's motion
Maurice Reply
what are the types of wave
Maurice
answer
Magreth
progressive wave
Magreth
hello friend how are you
Muhammad Reply
fine, how about you?
Mohammed
hi
Mujahid
A string is 3.00 m long with a mass of 5.00 g. The string is held taut with a tension of 500.00 N applied to the string. A pulse is sent down the string. How long does it take the pulse to travel the 3.00 m of the string?
yasuo Reply
Who can show me the full solution in this problem?
Reofrir Reply
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply
<< Chapter < Page Page > Chapter >>

Read also:

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, College physics for ap® courses. OpenStax CNX. Nov 04, 2016 Download for free at https://legacy.cnx.org/content/col11844/1.14
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'College physics for ap® courses' conversation and receive update notifications?

Ask